95 TA - The Beast
06-04-2013, 09:32 PM
Hey guys, I got some car audio gear I was going to put into my conversion van, but alas, since buying the house I cannot for-see getting back to making the van a priority for this stuff for quite some time, so I can't see it collecting dust.
I have two Kenwood Excelon amplifiers, both are new, I only pulled them out of the box to mock up the mounting scheme I was going with. They are the top end models from a couple years ago, both class D, one is a XR-4S 4-channel full-range amp and the other is an XR-1S mono sub amp. I have the original boxes and accessories and even a set of custom standoffs that allow you to stack both amps together for a really small installation footprint (I was going to mount both under one of the front seats in the van). Asking $400 for the pair (firm on that price) or $250 for the XR-4S by itself and $225 for the XR-1S by itself.
I also have a pair of Kenwood Excelon XR-W10F 10" low-profile subs that would be powered perfectly by the XR-1S that I would sell for $125 each or $225 for the pair if you buy the amps as a package deal for $625. Again, brand new in box, never installed or hooked up.
Specs:
XR-1S
600 watts RMS x 1 at 4 ohms (700 watts RMS x 1 at 2 ohms)
Peak output of 1500 watts
2x30amp fuses
4-gauge power and ground leads recommended
9-1/4"W x 2-1/16"H x 8-9/16"D small footprint
XR-4S
120 watts RMS x 4 at 4 ohms (150 watts RMS x 4 at 2 ohms)
300 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
Peak output of 300 watts x 4
2x30amp fuses
4-gauge power and ground leads recommended
9-1/4"W x 2-1/16"H x 8-9/16"D small footprint
XR-W10F
10" 4-ohm shallow-mount subwoofer
carbon-glass fiber composite cone with butyl rubber surround
push terminals handle up to 8-gauge wire
cast aluminum basket
power range: 50-350 watts RMS
peak power: 1,200 watts
mounting depth: 3-1/8"
I have two Kenwood Excelon amplifiers, both are new, I only pulled them out of the box to mock up the mounting scheme I was going with. They are the top end models from a couple years ago, both class D, one is a XR-4S 4-channel full-range amp and the other is an XR-1S mono sub amp. I have the original boxes and accessories and even a set of custom standoffs that allow you to stack both amps together for a really small installation footprint (I was going to mount both under one of the front seats in the van). Asking $400 for the pair (firm on that price) or $250 for the XR-4S by itself and $225 for the XR-1S by itself.
I also have a pair of Kenwood Excelon XR-W10F 10" low-profile subs that would be powered perfectly by the XR-1S that I would sell for $125 each or $225 for the pair if you buy the amps as a package deal for $625. Again, brand new in box, never installed or hooked up.
Specs:
XR-1S
600 watts RMS x 1 at 4 ohms (700 watts RMS x 1 at 2 ohms)
Peak output of 1500 watts
2x30amp fuses
4-gauge power and ground leads recommended
9-1/4"W x 2-1/16"H x 8-9/16"D small footprint
XR-4S
120 watts RMS x 4 at 4 ohms (150 watts RMS x 4 at 2 ohms)
300 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
Peak output of 300 watts x 4
2x30amp fuses
4-gauge power and ground leads recommended
9-1/4"W x 2-1/16"H x 8-9/16"D small footprint
XR-W10F
10" 4-ohm shallow-mount subwoofer
carbon-glass fiber composite cone with butyl rubber surround
push terminals handle up to 8-gauge wire
cast aluminum basket
power range: 50-350 watts RMS
peak power: 1,200 watts
mounting depth: 3-1/8"