Lots of Stuff for Sale - NOS Wet Kit, MSD, Autometer, Speakers, Printer

[xxsn0blindxx]

NOS Wet Kit - $175
Includes everything shown in pictures.

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3944.jpg

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3950.jpg


MSD Multi-Step Retard PN 8972 - $145
http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3948.jpg

MSD Blaster SS Coil PN 8207 - $30
http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3686_1.jpg

MSD 5 Ignition PN 5200 - $40

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3961.jpg

Armor All Gift Pack Unused- $10
Includes:
-Armor All Original Protectant
-Armor All Tire Foam Protectant
-Armor All Cleaning Wipes
-Armor All Car Wash Concentrate
-Armor All Wheel Cleaner
-Wheel Brush

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3954.jpg

Kenwood KFC-6909 6x9s - $45
Speaker Features
-Frequency Response: 28Hz - 30kHz
-Impedance: 4 ohms
-Magnet Weight: 15.6 oz
-Midrange: 2-3/4" PEI Film Cone
-Power Handling: 250 Watts
-Rubber Surround
-Sensitivity: 93dB
-Super-Tweeter: 13/16" PPS Film Dome
-Tweeter: 1" PEI Film Banalced Dome
-Woofer: 6" x 9" Pearl-Mica Injection-Molded Polypropylene Cone

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3957.jpg

Clarion SRR1322 5.25" Speakers - $25
-Polylaminate Woofer Cone
-Dynamic 1-9/16" PEI Tweeter
-Water- & UV-Resistant Cone
-Heat-Resistant Voice Coil
-Strontium Magnet
-80 Watts Maximum Music Power

http://i335.photobucket.com/albums/m451/xxsn0blindxx/Stuff%20For%20Sale/IMG_3960.jpg

[stenchmiester]

Is the nitrous kit a single nozzle setup for efi?

[xxsn0blindxx]

Yes I believe so. The guy I bought from had it on a 5.0 Mustang.

[MoCkiN U]

I would get the tape off the solenoids and get those part numbers to know what shots they are rated through so you can know what your jet sizes should be.

dibs on boost gauge if not already gone LOL.

[2 bad z's]

those look like nx noids ,they will handle 300 shot ,i would not put that much thru a single tho
I would get the tape off the solenoids and get those part numbers to know what shots they are rated through so you can know what your jet sizes should be.

dibs on boost gauge if not already gone LOL.

[gottwins?]

I'll take the armorall kit, where are you located?

[Kory 88Iroc lt1]

how does the msd5 compare to the 6a? would this work on an lt1 with the adapter wiring? thanks,
kory

[xxsn0blindxx]

MSD 5 is stated to work with any car that uses a distributor. I can't find anything that specifically compares the 5 to the 6A, but here is what I have found for the specs.

Here (http://www.msdpower.com/download/5200.pdf) are the installation instructions.

MSD-5
Operating Voltage: +12 VDC Negative Ground
Current Requirements: 6 Amps Max
RPM Range: 6,000 RPM (8 cyl.)
Spark Duration: 20° Crank Rotation
Energy Output Max: 140 mJ Stored Energy (inductive ignition)
Weight and Size: 1.5 lbs, 8''Lx3.5''Wx2.25''H
Voltage Output Max: Primary: 375 Volts Secondary: 40,000 Volts (Blaster Coil)

MSD-6A
Spark Energy: 105 to 115 mJ (per spark)
Primary Voltage: 460 to 480 volts
Secondary Voltage: 45,000 volts (Tested with Blaster Coil)
Spark Series Duration: 20° crankshaft rotation
RPM Range: 15,000 RPM with 14.4 volts
Voltage Required: 12 to 18 volts (negative ground)
Current Draw: 1 amp per 1000 RPM
Dimensions & Weight: 8" L x 3.5" W x 2.25" H, 2.75 lbs

[xxsn0blindxx]

BUMP - I'm open to offers

[xxsn0blindxx]

Bump - Somebody has to want this stuff

[xxsn0blindxx]

Bump cleaned up the list.