View Full Version : Custom exhaust work/welding
1siksrt
07-23-2008, 10:09 PM
who does kick ass custom work?? I took my car to waukesha muffs and pipes and it was terrible... Joel had to fix the welds cause it leaked so bad...
Now I need some more work done and not sure who to go TO...
STANMAN
07-23-2008, 10:17 PM
Skeeter.
sloLs1
07-23-2008, 10:18 PM
i just did a custom 3in exhaust on a srt... its wasnt too bad at all.... what are you looking to do???
1siksrt
07-23-2008, 10:27 PM
i just did a custom 3in exhaust on a srt... its wasnt too bad at all.... what are you looking to do???
Um some welding and flanges put on... currently have exhaust but it got all f-ed up from C-clamps... So Now Im gonna make it a dump exhaust....
Poncho
07-23-2008, 10:36 PM
Hillbilly.
Russ Jerome
07-23-2008, 10:37 PM
An electric exhaust dump is worth the money if its in the budget.
Flying down the freeway and hitting a switch results in flames
shooting strait out your downpipe to the road :) Its realy not
that loud on a turbo car, you will find yourself using it more
often than you would think. I likes my McCord model, $250.
GRAMPS SS
07-23-2008, 10:38 PM
hillbilly FTW
1siksrt
07-23-2008, 10:40 PM
An electric exhaust dump is worth the money if its in the budget.
Flying down the freeway and hitting a switch results in flames
shooting strait out your downpipe to the road :) Its realy not
that loud on a turbo car, you will find yourself using it more
often than you would think. I likes my McCord model, $250.
Ya This will not be a DD in the near future... Its gonna dump just passed the gas tank and at an angle similar to a exhaust i saw on the internet made by a company called ragetek
DurtyKurty
07-23-2008, 10:54 PM
I don't really have the facility to do entire exhaust systems, but if you only need a flange or something straight forward, I can help you out. You can see some of my exhaust stuff here (http://picasaweb.google.com/recklessford/TurboRanger). Keep in mind that some of those pieces were previously used components. :)
Russ Jerome
07-23-2008, 10:57 PM
You can see some of my exhaust stuff
http://lh6.ggpht.com/recklessford/SGzJ8jpf-MI/AAAAAAAAABI/xcfwmsYffEg/2K%20Ranger%20Header.jpg?imgmax=512
Nice header, I can apreciate the workmanship!
1siksrt
07-23-2008, 10:57 PM
I don't really have the facility to do entire exhaust systems, but if you only need a flange or something straight forward, I can help you out. You can see some of my exhaust stuff here (http://picasaweb.google.com/recklessford/TurboRanger). Keep in mind that some of those pieces were previously used components. :)
Sounds good, where are you located?? We would have to rip off the downpipe to do it right, but it would not be too bad
:thumbsup
DurtyKurty
07-23-2008, 11:02 PM
Wauwatosa. Send me a PM, and we can set something up tomorrow.
spindler27
07-24-2008, 12:48 AM
hillbilly FTW
does this hillbilly happen to have a southern accent and a beard? maybe just got laid off at walltech?
stealthy1ss
07-24-2008, 05:34 PM
Just throwing out a long shot here but if you don't mind traveling to Lake Geneva you could go to RPM's. Randy there does a kick ass job and it isn't pricey.
GRAMPS SS
07-24-2008, 10:50 PM
does this hillbilly happen to have a southern accent and a beard? maybe just got laid off at walltech?
no on the lay off....he's retired after 30 plus years of doing exhaust work...now he has his own shop...and does have a southern accent...and you can't beat his work for the money.....:thumbsup
1siksrt
07-24-2008, 11:44 PM
^^^where is this shop???? I might need more done then kurt can do out of his garage
Powered by vBulletin® Version 4.2.0 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.