PDA

View Full Version : LT1 Y-Pipe



Heat Seeker WS6
04-03-2007, 12:20 AM
Mufflex Y-Pipe for single cat LT1. Will bolt to stock manifolds
$50

sloLs1
04-03-2007, 12:58 AM
what diameter piping??? condition???


thank you

Beagle
04-03-2007, 01:10 AM
that wouldnt work on my car will it? i no i have two cats but what if i take off the cats? the driver side cat would prolly make things difficult.

Heat Seeker WS6
04-03-2007, 01:11 AM
Its in very good cond, but its not coated at all. Not sure of diameter, but its larger than stock.

These are the only shots I have off hand of it- sorry about the other junk in the pics...
http://i89.photobucket.com/albums/k213/Heat_Seeker_WS6/Copy3of213384_4_full.jpg

http://i89.photobucket.com/albums/k213/Heat_Seeker_WS6/Copy5of213384_3.jpg

Beagle
04-03-2007, 01:21 AM
hey that looks like it would work on my car.

Heat Seeker WS6
04-03-2007, 01:22 AM
all you need is single cat setup & it'll go on

Beagle
04-03-2007, 01:33 AM
can i just take both cats off?

Heat Seeker WS6
04-03-2007, 01:39 AM
Hmm... I dont know enough about the dual cat cars to answer that, but look at the top pic- does that look like it can work? You would need to weld a cat onto it & that'll then bolt onto the intermediate pipe.

Beagle
04-03-2007, 01:47 AM
it really looks like it would work. i pm'ed ron so he'll no for sure. i'll let you no.

juicedimpss
04-03-2007, 09:24 AM
could always make a "test pipe"

sloLs1
04-03-2007, 12:23 PM
could always make a "test pipe"


thats the way to do it... but his maro is OBD2.... so he might throw a CEL for not having a cat. I am sure he can find a o2 sim?!?!

i think thats a great deal.... you need that nick!

Heat Seeker WS6
04-03-2007, 12:33 PM
Nick its at my parents place, should I pick it up so you can look at it/have it?

juicedimpss
04-03-2007, 12:40 PM
thats the way to do it... but his maro is OBD2.... so he might throw a CEL for not having a cat. I am sure he can find a o2 sim?!?!

i think thats a great deal.... you need that nick!

thats a perfect reason to put obd1 swap in the car,plus its cheap to tune.

Heat Seeker WS6
04-03-2007, 04:04 PM
Did some measuring of it- 2 1/2" each side to a 3 1/2" out

Beagle
04-03-2007, 05:22 PM
hmmm....... you might have to hold on to that for me. i'd have to get my car in the air to no for sure if i can make something work.

Heat Seeker WS6
04-06-2007, 01:17 PM
Here's some pics I just took of it
You can see the pass drivers side O2 bung

http://i89.photobucket.com/albums/k213/Heat_Seeker_WS6/P1010265.jpg

http://i89.photobucket.com/albums/k213/Heat_Seeker_WS6/P1010269.jpg

http://i89.photobucket.com/albums/k213/Heat_Seeker_WS6/P1010270.jpg

sloLs1
04-06-2007, 01:28 PM
$50 sounds like a good deal

Heat Seeker WS6
04-06-2007, 01:29 PM
I have it at my store today in Franklin if you wanna swing by & check it out. Beagle- you too....

Beagle
04-06-2007, 05:14 PM
i'm on my way!

Heat Seeker WS6
04-06-2007, 05:16 PM
ha ha run forest!!
Im locking the store down!!!!!!! :rolf :rolf

Heat Seeker WS6
04-06-2007, 05:16 PM
j / k