PDA

View Full Version : WTB: SBC 4-bolt



350-Z28
01-15-2007, 01:36 AM
Yeah I sold all my stuff before happenin upon a clean rolling chassis to get together so i can have my V8 back. Just looking for a cheap good 4-bolt small block, bare block, short block, or complete motor so long as its cheap as it will be built so not much stock would be kept. If you have a built shortblock also let me know. Plans for the motor will be a stroker and twin turbocharged on around 15psi to a 20 psi absolute max. If you have anything or hear of anything please let me know. Thanks guys.

Andrew
262-352-0261

sloLs1
01-15-2007, 09:52 AM
i know we have some 4 bolt SBC's sitting at my work.... i will let know you what i can do for you! (either i will pm you later tonight or tomorrow!)

Memphis
01-15-2007, 10:15 AM
I've got a block all machined, bored out ready to build. $200

350-Z28
01-15-2007, 12:27 PM
Thanks for the replies! Memphis I'll pm you once I find out what all sloLS1 has at his work. But that being already machined is tempting. How much was it bored over?

MY FYN 79
01-15-2007, 05:55 PM
I have my old 383 block I would now sell. Its an 010 020 4 bolt main casting, has been stroker clearanced, zero decked, .030 over, studded mains, line bored etc. etc.

$300 takes it.

Memphis
01-15-2007, 08:38 PM
I believe its .030 over...

350-Z28
01-16-2007, 01:45 AM
damn i didn't expect there to be this many good deals out there....79 was that a 4 inch crank? What were the rod lengths? Just so I could order the right stuff and not have to worry.

Poncho
01-16-2007, 10:42 AM
dad has a stock 305 outta a '86 iroc ready to go, unassembled, but has reciprocating assy and block, already cleaned up, honed, magnafluxed, etc.

madmike
01-16-2007, 05:13 PM
I have a early 70's engine that was running, truck 4-Bolt main and the heads have brand new 2.02 valves in them, and I think I have just about everything with it as a complete engine, either the carb or the intake is missing, I forget wich but I am going up to the shop in about 30 minutes

$350.00

I also have a couple Z-28 LT1's, one has a cracked piston I was going to make a 383 LT1 out of it, its complete, fuel rails, TB, Manifolds yada yada its a 94 Z-28, and the 95 Z-28 LT1 is a runner with 112k miles complete

sloLs1
01-16-2007, 05:57 PM
i dont think i will be able to beat those prices... sorry!

but i do have a 40 over with pistons and ready to go

and a regular stock block not machined

350-Z28
01-17-2007, 01:31 AM
Going Gen 1 small block with this one. Was that engine completely stock with 2.02 valves? Any mods done to engine at all? I know for $350 i doubt it but worth a shot lookin into.

madmike
01-21-2007, 10:52 AM
Going Gen 1 small block with this one. Was that engine completely stock with 2.02 valves? Any mods done to engine at all? I know for $350 i doubt it but worth a shot lookin into.
Yes the engine has like 118k on it but the heads just had a valve job and new 2.02 intake valves installed. The guy I bought the engine from siad the engine was runnning good but started using oil through the heads so he pulled the heads and have the valve job done. I bought the engine for my 85 Grand Prix but just sold that to pay bills. and the guy who bought it has a 400 for it so he did not buy the enige with it. So its still for sale for $350.00 located in Portage, WI 53901

MY CELL IS 608-617-2401.

Mike