View Full Version : Any good shops in the area
1loudrex
01-07-2007, 09:13 PM
Ive got a 2002 Wrx and I need the clutch replaced. I have the clutch kit but ill need the flywheel resurfaced.
Ive got Automatic Transmission and Design in mind since I have a few buddies that work there, but any other shops with a decent price would be good to.
Thanks for any help
Dan
Flicktitty
01-07-2007, 09:15 PM
uh, i Know Jake (topstreet) has done some Sube work he might do it for you? i'm not sure though or maybe BEE Yond might do it to?
ThatWhiteCivic
01-07-2007, 11:12 PM
Yeah Bee did my buddy Mark's clutch and tranny on his Sube :thumbsup
TopStreetDsm
01-07-2007, 11:39 PM
Thanks Flick, But I am down to basically working on my car and truck at this point... (and twicks69's tranies :p) Good luck to you with the project LoudRex!
Flicktitty
01-08-2007, 12:32 AM
yeah i kindda figured that but i'd just throw it out there.
Where you been i haven't seen you on much latley?
sloLs1
01-08-2007, 07:15 AM
Ive got a 2002 Wrx and I need the clutch replaced. I have the clutch kit but ill need the flywheel resurfaced.
Ive got Automatic Transmission and Design in mind since I have a few buddies that work there, but any other shops with a decent price would be good to.
Thanks for any help
Dan
my shop would do it... i can get you a price today...
tommyt5078
01-08-2007, 09:42 AM
I say visit the subaru forums NASIOC.COM go to local forum MWSOC and find Tim Sanderson................
jbiscuit
01-08-2007, 09:54 AM
+1 for Tim Sanderson
TopStreetDsm
01-08-2007, 12:28 PM
Where you been i haven't seen you on much latley?
I have been on computer probabition...:rolf No... I just moved... Again... and I have been with out that there inter-web for a while. Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.
sloLs1
01-08-2007, 02:59 PM
my shop would do it... i can get you a price today...
your cost would be $460 for the labor.... let me know if your intrested... i have done subies before... they arent bad at all.... A LOT easier than a EVO!!!
.....Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.......
:rolf
Flicktitty
01-08-2007, 03:32 PM
:rolf that sucks where'd you end up moving too.
I have been on computer probabition...:rolf No... I just moved... Again... and I have been with out that there inter-web for a while. Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.
TopStreetDsm
01-08-2007, 09:13 PM
Back out in waukesha again...
uh, i Know Jake (topstreet) has done some Sube work he might do it for you? i'm not sure though or maybe BEE Yond might do it to?
we've done a few...wrx/sti no biggy!!! tranny rebuilt also available in 2-3 day wait... sube trannys break quite often...
:thumbsup
sube tranny install: $300.00
resurface flywheel: $50.00
all done in a day too!!!
Yes we can beat any written or advertised price gauranteed!!!
I'll update pixs of our NEW in-house dynamometer, Fabrication division, Show room, Race car section, Custom muffler bays, General Auto maintenance bays, and tire machine section..... 9 bays total..... with tons of outlot parking(10-12 in front & 40-50 car in the rear)... car show maybe.. or even dyno days w/ a BBQ fest.... I'll upate on car shows/dyno days/BBQs!!!
8025 N. 76th ST. near Brown Deer.... come check it out!!!
TurboAWD2.0
01-12-2007, 04:12 AM
Or, and no offense to anyone here, take the flywheel to napa. It's $36 or something like that to get it resurfaced. Then, do the whole thing yourself in your garage ;)
EDIT:
On a side note, what mods did you have when you ran that 14.12 sec quarter?
Bart H
01-12-2007, 02:28 PM
Tim Sanderson FTW!
if you are mechanically inclined then yes do it in your garage... be careful that tranny can come down on you.... :thumbsup
1loudrex
03-12-2007, 09:52 PM
Or, and no offense to anyone here, take the flywheel to napa. It's $36 or something like that to get it resurfaced. Then, do the whole thing yourself in your garage ;)
EDIT:
On a side note, what mods did you have when you ran that 14.12 sec quarter?
Perrin Uppipe.
95excoupe
03-12-2007, 10:42 PM
we've done a few...wrx/sti no biggy!!! tranny rebuilt also available in 2-3 day wait... sube trannys break quite often...
:thumbsup
sube tranny install: $300.00
resurface flywheel: $50.00
all done in a day too!!!
Yes we can beat any written or advertised price gauranteed!!!
I'll update pixs of our NEW in-house dynamometer, Fabrication division, Show room, Race car section, Custom muffler bays, General Auto maintenance bays, and tire machine section..... 9 bays total..... with tons of outlot parking(10-12 in front & 40-50 car in the rear)... car show maybe.. or even dyno days w/ a BBQ fest.... I'll upate on car shows/dyno days/BBQs!!!
8025 N. 76th ST. near Brown Deer.... come check it out!!!
yes, its very true. i say one of the best shops in wi. and good quality of work. :thumbsup
people say beeyond is blah blah, but my point of view they just are haters.
bearsek
03-12-2007, 11:14 PM
We work on subies all the time(Extreme parts). They are for sure easier than evo clutches
civic600
03-18-2007, 01:41 PM
take it to extreme parts.....they do awesome work
Powered by vBulletin® Version 4.2.0 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.