Got a Winter Build Planned?

[biggsGTP]

Alright just seeing what people are doing (if anything) this winter/early spring as far as build's on the cars. I just took my new job as a ironworker so my mod list savings can finally start up agian. . . Here is my winter build list, let me know what you guys think, and post up your lists if you have any plans. PS: My car is a 2000 Grand Prix GTP

Winter/Spring Build 2006-2007

1. Stattama 62-1 Turbo Kit
2. Stattama ST2 Cam
3. IS3 Heads
4. ZZP 4340 Input Shaft
5. ZZP Hardned 4th Gear Clutch Shaft
6. ZZP 3250rpm Torque Converter
7. BT Racing 75mm N* TB Kit
8. Mototron 65# Injectors
9. ZZP Engine Gasket Kit
10. Cometic MLS .052 Head Gaskets
11. ZZP PowerLog
12. 105# Springs

~Biggie :thumbsup

[Waver]

I am going to be aquiring parts between now and january, and install them in febuary, however I dont know what I am going to pick up as I am just getting other peoples used junk to go fast.

[Heat Seeker WS6]

383 LT1
Bigger wheels in back
Paint?

[biggsGTP]

Forgot to add 2 to my previous list. . .

13. 3" Manual Cutout
14. Dual (front & rear banks) Wideband setup (got the idea from local member)

[MurphysLaw88GT]

An MG-42:goof ........................as for cars, nothing yet. money is tight

[rally_scort]

plans for the wagon

1.Get some new suspension
2.Get it resprayed
3.Put it on the juice:rolf :rolf :rolf

[deciuss]

my plans are to find a used trans and then rebuild it due to mine is starting to go.

[UnderPSI]

2002 club Car golf cart

Full tube frame chassis lengthend 10" widened 6"

Roll cage

4 link rear suspension

Electric start 600cc snomobile engine.

Coil overs

one set of off road and one set of street tires and rims.

Thats all for now.

[Flicktitty]

^^^ Badass!!!

[Brandon W.]

The same car ive been working on for the past 5 months..The Red Dizzum

[JC70SS]

NO!!! Thank God.

[BOSS LX]

2002 club Car golf cart

Full tube frame chassis lengthend 10" widened 6"

Roll cage

4 link rear suspension

Electric start 600cc snomobile engine.

Coil overs

one set of off road and one set of street tires and rims.

Thats all for now.
:headbang

[ProjectCamaro]

Finishing up my nitrous install.
Cam
Clutch
gears
New Paint
Alarm
Suspension

[Bobby "Big Daddy" Flay]

I just installed my new clutch, i'm now good till spring, I hope

[Al]

Build a boat.

[mr. meaner]

Finish the house.

[Rocket Power]

I am going to marry my 64 Cutlass with an Olds engine of modest displacement and put some interior in it and hopefully be ready for spring.

[A B4C Z]

Thinking about doing some heads and maybe a new cam.

Kyle

[Want_Notch]

Get rid of my 4.6 and put an LS1 in it's place...........

[MY FYN 79]

Swap *most* of my 383 guts into a 400 block.

[USMARINE1108]

What's winter? :stare

Just kidding. It get's to 50 or so down here. I'm planning on a 12 bolt with some 410's.

[Crawlin]

didn't HAVE any plans of must do's... but now I HAVE to have plans :)

[jbiscuit]

didn't HAVE any plans of must do's... but now I HAVE to have plans :)


I can help:

part out the existing motor and selling the roller in favor of a carb'd big block Chevelle on the squeeze??? :rolf :thumbsup

[juicedimpss]

i vote to make it bigger,and put more nitrous on it.

[Crawlin]

i will have to say that launch was pretty cool, even if it was off the footbrake, hahaha. can't believe dude in the camera shop didn't even have a pic

[juicedimpss]

i will have to say that launch was pretty cool, even if it was off the footbrake, hahaha. can't believe dude in the camera shop didn't even have a pic
damn,i completely missed that pass. :crying

[Prince Valiant]

This is what I've started building....

360, bored .040 over
11.5:1 Wiesco forged pistons
Forged 4.00 inch crankshaft for a total of 410ci's.
Ported Indy small block AL heads...flows 330cfm/210cfm.
Mildon main caps, held by ARP main studs.
Eagle H-beam rods, 6.125 inches long
Still working on an intake manifold...likely from Indy.
Hughes mechanical cam ~250-255 degrees duration @ .050, ~ .600 lift, migth go with roller cam.
TTi 1 3/4 headers (might go with fenderwell 1 7/8th inch headers)
Holley 850cfm carb
A-727
8 3/4 rear, 3.73

It won't be done next year though...the engine/trans mabye though...

[Larrygto]

Headers, tune and DRs for a start.

[MurphysLaw88GT]

This is what I've started building....

360, bored .040 over
11.5:1 Wiesco forged pistons
Forged 4.00 inch crankshaft for a total of 410ci's.
Ported Indy small block AL heads...flows 330cfm/210cfm.
Mildon main caps, held by ARP main studs.
Eagle H-beam rods, 6.125 inches long
Still working on an intake manifold...likely from Indy.
Hughes mechanical cam ~250-255 degrees duration @ .050, ~ .600 lift, migth go with roller cam.
TTi 1 3/4 headers (might go with fenderwell 1 7/8th inch headers)
Holley 850cfm carb
A-727
8 3/4 rear, 3.73

It won't be done next year though...the engine/trans mabye though...
Nice:thumbsup

[sacstoy02gt]

uncork the exhaust finally :rolleyes:
DS loop
maybe 3.73s (3.27s in it now)
new seats
battery relocation

nothing fancy...need to buy a boat this winter/early spring more than I need to mod the car.

[BAD LS1]

Never modding again! Time for underhood mirrors and fancy red convoluted tubing cuz its now a driving show car hahahahahahah!

Time to get one of these... Yamaha Raptor 700R

http://www.yamaha-motor.com/assets/content/images/600/07raptor700r_blue_4_copy_4a950c08.jpg

[Cryptic]

like BAD LS1 I have diversified my spending into other toys.

[SLOWC5]

demodding and selling the vette. different car in spring.

JEFF

[DoubleAron]

Mine has been more of a Winter of 04, Spring Summer Fall and Winter of 05, Spring Summer Fall and Winter of 06, it finally should be ready late
06 early 07.

[HRSEPLA]

Looks good! I cant wait to see it! Isnt your engine tie down on the wrong side?:)

[BAD LS1]

I think thats from the engine hoist chain?

[FourEyedFord]

Mine has been more of a Winter of 04, Spring Summer Fall and Winter of 05, Spring Summer Fall and Winter of 06, it finally should be ready late
06 early 07.

Looks good in there Aaron! The race is on for the fastest blow through! :chair: :D

My plans don't involve any changes really except for the new blower. I mainly just want to get it down the track next year!!!

[HRSEPLA]

I think thats from the engine hoist chain?

I know, just messing with A- ron, you just worry about your hose clamps on your fuel line. lol:)

[DoubleAron]

One is the hoist chain and the other is just holding it in place as a safety brace. It is just on the motor mounts now with no trans so I just chained it to be safe pushing it in and out of the garage.

Just checking everything to see how my fan/radiator fits, run fuel lines, all that other time consuming garbage. Converter should be here late
this week/early next and then it will all go in as a whole.

Thanks guys, can't wait to finally have something running!

Come on Robert you know I don't stand a chance.;)

[Slow Joe]

I think I might be putting together a book shelf or something :rolf

[BOSS LX]

Mine has been more of a Winter of 04, Spring Summer Fall and Winter of 05, Spring Summer Fall and Winter of 06, it finally should be ready late
06 early 07.
:headbang

[FourEyedFord]

Come on Robert you know I don't stand a chance.;)

That is if the motor stays together better than it has been......

You know you'll change some things before next year is over ;) , or maybe even before the end of winter! :goof

[DoubleAron]

You know you'll change some things before next year is over ;) , or maybe even before the end of winter! :goof

What are you trying to say?:D

[Korndogg]

I have something planned but I doubt Ill be able to afford it this winter :(

Im taking donations. anyone?

[FourEyedFord]

What are you trying to say?:D

You know......its in my sig. :headbang

[scottie K]

just updating

[88blknotch]

Finally get the small block running.


Or maybe a big block.




Maybe a Turbo.






Damn A.D.D. LOL

[TURTLE]

big block in the silver car...

oil changes and basic mant. on the black car from texas.... ;)

[TheBlueSupra]

I've already started mine.

10 point cage
stroker motor
new intake mani
new exhaust mani
and a neal chance converter
all going in the supra

[Poncho]

if the trans am ever sells

short throw shifter
06 tails
HPE S Cam
Pushrods
Patriot Golds
Retainers
Valve Seals
Eibachs
HSV Spoiler
Racemesh Grille Inserts
Piece together new stereo since the dang mustang has it all now.

and the Mustang:
Roush Louvers
Tint

[67-400]

Goin w/the Mini-Ram baby!!! I've eyed this friggin intake up for the past 10 years, finally can afford it. In addition to that, MSD 6AL Ignition. I wonder how long my stock block & Crank will last. :confused Maybe a new stroker kit will be next winters project? :headbang Actually plannin doin it over Thanksgiving week....vacation. Upgrading from my SLP Twin runners, can't wait to see the difference

4110

[Nix]

Kmove, Im gonna need updates on this progress. Good luck loser:thumbsup