Darrell
07-18-2006, 03:33 PM
Complete 425 cubic inch 9.5 deck small block Ford
- Professionally built
- Fully balanced rotating assembly
- 13.32:1 compression
- Probe forged pistons
- Hellfire rings
- Scat Lite weight crank
- Pro Lite rods
- ARP main studs, head studs and oil pan studs
- DSS Main Girdle
- Melling oil pump
- Canton oil pan
- Cometic head gaskets
- Total Engine Airflow 235CNC TFS R series heads 358cfm intake and 270 cfm exhaust with new Isky Tool Room valve springs and titainium retainers.
- Crane Gold series rockers
- Rocker Stud Girdles
- Custom Comp Cams solid roller 268/276 duration at .050, .705/.673 lift
- Comp Cams solid roller lifters
- Edelbrock Super Victor ported by M2 Race Systems
- MSD Pro Billet distributor
- Taylor 409 plug wires
- CSR electric water pump
- Fabricated valve covers
- SFI Flexplate
- SFI balancer
- 2" stepped to 2 1/8" headers
- aluminum motor plate
- Powermaster starter
- Complete intake to oil pan!!!
- Drop in and go!
- dyno sheet, cam card and other paper work available
$7500 complete intake to oil pan or $6500 minus intake and distributor.
In a 3016 pound Mustang this motor runs 9.36 at 143mph with a 1.32 60 foot. Here it run and see it drive! Many pictures and videos are available. I also have a PA Super Comp C4, Coan 8" 6000 stall converter, AJE chromoly K-member, manual rack and aluminum driveshaft that I will make a package deal on for $9500. Need to sell quickly to finish new engine. Will deliver. Feel free to contact me with any questions at darrell1@charter.net
- Fox Lake stage 2 TFS twisted wedge heads with .700 lift solid roller springs
SOLD!
- Crane 1.6 ratio SBF gold race rockers (idle time only) - SOLD!
- Edelbrock Super Victor 302 intake drilled and tapped for fogger - SOLD!
- Weld Draglites (set of 4 - 5 lug unilug) - 15x3.5 x 1.75 back spacing with 26x4.5 M/T ET Fronts and 15x10 x 6.5 back spacing with 28x10.5W M/T slicks - $800
- Edelbrock RPM nitrous plate system with purge and nitrous gauge - $300
located in North Fond du Lac
darrell@wisconsinstreetdominators.com
- Professionally built
- Fully balanced rotating assembly
- 13.32:1 compression
- Probe forged pistons
- Hellfire rings
- Scat Lite weight crank
- Pro Lite rods
- ARP main studs, head studs and oil pan studs
- DSS Main Girdle
- Melling oil pump
- Canton oil pan
- Cometic head gaskets
- Total Engine Airflow 235CNC TFS R series heads 358cfm intake and 270 cfm exhaust with new Isky Tool Room valve springs and titainium retainers.
- Crane Gold series rockers
- Rocker Stud Girdles
- Custom Comp Cams solid roller 268/276 duration at .050, .705/.673 lift
- Comp Cams solid roller lifters
- Edelbrock Super Victor ported by M2 Race Systems
- MSD Pro Billet distributor
- Taylor 409 plug wires
- CSR electric water pump
- Fabricated valve covers
- SFI Flexplate
- SFI balancer
- 2" stepped to 2 1/8" headers
- aluminum motor plate
- Powermaster starter
- Complete intake to oil pan!!!
- Drop in and go!
- dyno sheet, cam card and other paper work available
$7500 complete intake to oil pan or $6500 minus intake and distributor.
In a 3016 pound Mustang this motor runs 9.36 at 143mph with a 1.32 60 foot. Here it run and see it drive! Many pictures and videos are available. I also have a PA Super Comp C4, Coan 8" 6000 stall converter, AJE chromoly K-member, manual rack and aluminum driveshaft that I will make a package deal on for $9500. Need to sell quickly to finish new engine. Will deliver. Feel free to contact me with any questions at darrell1@charter.net
- Fox Lake stage 2 TFS twisted wedge heads with .700 lift solid roller springs
SOLD!
- Crane 1.6 ratio SBF gold race rockers (idle time only) - SOLD!
- Edelbrock Super Victor 302 intake drilled and tapped for fogger - SOLD!
- Weld Draglites (set of 4 - 5 lug unilug) - 15x3.5 x 1.75 back spacing with 26x4.5 M/T ET Fronts and 15x10 x 6.5 back spacing with 28x10.5W M/T slicks - $800
- Edelbrock RPM nitrous plate system with purge and nitrous gauge - $300
located in North Fond du Lac
darrell@wisconsinstreetdominators.com