biggsGTP
07-07-2006, 06:28 PM
Completely Rebuilt 305 HO ~~~~~ ONLY 7000miles on rebuild!
- Bored .030 over
- 3 Angle valve job
- High performance Edelbrock cam
- Edlebrock Performer intake
- Edlebrock Performer 650 four barrel carburetor
- 1.6:1 Roller Rockers
- Oversized Valves
- Double Roller timing chain
- Edlebrock Valve covers
- New water pump
- All new bearings & seals
- New connecting rods & pistons
- Balanced to 7500rpms
- New fuel pump
- All emissions removed
Full MSD Ignition
- MSD billet distributor
- MSD Coil Blaster 2
- MSD 6AL ignition control box w/ soft touch rev limiter
Completely rebuilt Rear End (250 miles on rebuild)
- 4:10 Richmond gears
- Eaton limited-slip differential
- New bearings & seals
- New Axles
Misc. Parts
- Clutch replaced when motor work was done
- Custom made 10.4mm Taylor Wires
- New Headers (never installed)
- New Suspension & brakes
- Newer Tires
- CD Player w/ new speakers
http://img.villagephotos.com/p/2005-11/1106558/steve2.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve3.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve1.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve6.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve4.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve5.jpg
Runs & Drives GREAT ~ Over $7000 invested
Asking $3200
Contact Steve: 920-858-2477 ( or post here lol )
~Biggie
- Bored .030 over
- 3 Angle valve job
- High performance Edelbrock cam
- Edlebrock Performer intake
- Edlebrock Performer 650 four barrel carburetor
- 1.6:1 Roller Rockers
- Oversized Valves
- Double Roller timing chain
- Edlebrock Valve covers
- New water pump
- All new bearings & seals
- New connecting rods & pistons
- Balanced to 7500rpms
- New fuel pump
- All emissions removed
Full MSD Ignition
- MSD billet distributor
- MSD Coil Blaster 2
- MSD 6AL ignition control box w/ soft touch rev limiter
Completely rebuilt Rear End (250 miles on rebuild)
- 4:10 Richmond gears
- Eaton limited-slip differential
- New bearings & seals
- New Axles
Misc. Parts
- Clutch replaced when motor work was done
- Custom made 10.4mm Taylor Wires
- New Headers (never installed)
- New Suspension & brakes
- Newer Tires
- CD Player w/ new speakers
http://img.villagephotos.com/p/2005-11/1106558/steve2.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve3.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve1.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve6.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve4.jpg
http://img.villagephotos.com/p/2005-11/1106558/steve5.jpg
Runs & Drives GREAT ~ Over $7000 invested
Asking $3200
Contact Steve: 920-858-2477 ( or post here lol )
~Biggie